#CHANGE ACCESS CODE ON AN IEI KEYPAD HOW TO#

Programming will not be lost during battery change. If the keypad backlighting fails to operate, the batteries may require replacing. Start at STEP 1 to program a new PIN number The LED will flash twice and all lights will go out indicating the keypad has been reset.Ĥ. Press and hold the PROGRAM and UP/DOWN Keys together for approximately 5 seconds.ģ. Ensure that the number pad backlighting is off.Ģ.

If the keypad has already been programmed or at any time the programming should be erased and started from the factory default, follow these steps.ġ. * RESETTING THE KEYPAD (FACTORY DEFAULT):

During this 15 seconds, ANY key will operate the opener. NOTE: Keypad will remain active for 15 seconds after a successful entry is made. Press number key corresponding with the desired door (1, 2, or 3). STEP 3) OPERATING THE KEYPAD WITH THE OPENER(S)Ĥ. See STEP 3 MULTI-DOOR OPERATION for further instruction.

This completes the programming of multiple doors.

Repeat steps 1 through 6 to program second and third openers.

Press the UP/DOWN key 3-4 times slowly until the garage door opener operates. Press the number of the desired door (1, 2 or 3).Ħ. Place desired garage door opener (1, 2, or 3) into PROGRAMMING MODE.ĥ. PROGRAMMING THE KEYPAD TO MULTIPLE OPENERS (UP TO 3)ġ.

If LED did not blink twice and shut off, please see RESETTING THE KEYPAD (FACTORY DEFAULT) section.

The keypad is now ready to program to multiple garage door openers.

The keypad is now programmed with a PIN number and set up for multi opener operation.

Enter the total number of openers that keypad will be operating. (This pin number will be the same for all the doors.) Then follow these additional steps.ģ. Program the keypad with a Personal Identification Number (PIN) as described in step 1. STEP 2B) PROGRAMMING THE KEYPAD FOR MULTIPLE OPENERS (UP TO 3) Programming the keypad to the opener must be completed within the 30 seconds. Note: The openers LEARN LED will time out in 30 seconds.

Press & Release the learn code button once. Place the garage door opener into programming mode:ġ. Note: The learn code buttons are normally located under the lens covers on earlier models. Garage Door Openers manufactured between 1995 to 2011 and all external receivers The round LED will go out and the long LED will begin flashing purple. Press and hold the program button until the round LED turns blue, then release.Ģ. Place the garage door opener into programming mode. All buttons perform the same function and programming is the same for all types shown above. There are 3 types of programming button pads. Putting the garage door opener into programming mode. See STEP 3 SINGLE DOOR OPERATION for further instruction

This completes the programming of a single door.

Press the UP/DOWN key 3 to 4 times slowly until the garage door opener operates. Place garage door opener into PROGRAMMING MODE as illustrated below.Ģ. STEP 2A) PROGRAMMING THE KEYPAD TO 1 OPENER- (if you have more than one garage door skip to the next step.)ġ.

If LED did not blink twice and shut off, please see RESETTING THE KEYPAD (FACTORY DEFAULT) section.

See STEP 2B PROGRAMMING FOR MULTIPLE OPENERS if using the keypad to operate up to 3 doors.

The keypad is now programmed with a PIN number and ready to program to the garage door opener(s).

Program the keypad for the first time* with a Personal Identification Number (PIN).

#CHANGE ACCESS CODE ON AN IEI KEYPAD HOW TO#

How to program the Wireless Keypad, Genie garage door openersįor use with Genie Intellicode® garage door openers Wait 15 seconds until the backlighting shuts off before entering a valid PIN or resetting the keypad to reprogram.The Keypad LED, PROGRAM key and Number pad black light will flash rapidly indicating a problem with the programming or invalid PIN entry. The Keypad LED and PROGRAM key will flash slowly and the number pad backlight will remain on for 15 seconds indicating a successful program or valid pin number has been entered. The keypad LED will flash each time a key is pressed and entry is accepted. Reinstall the battery compartment door to begin programming. *It is recommended to complete the programming before mounting the keypad.Īctivate the Genie wireless keypad (GK-R) by opening the battery cover compartment and pull the protective tab. GK-R (Genie Garage Door Opener Keypad) Programming Quick Reference Card

Change access code on an iei keypad